fluid temperature造句
例句與造句
- If the fluid temperature is too high or contains the erosive substance , it would break the hoses
流體溫度過高或流體帶腐蝕性成份，可能會令軟管破裂。 - Li xian ye heating and refrigeration are placed chu yecao , and equipped with automatic control system fluid temperature
洗液的加熱和冷凍均置于儲液槽中，且配有液溫自動控制系統。 - Although the phere will normally dissolve in a few hours , the dissolving rate is a function of fluid temperature , fluid movement , friction , and absorbability of the crude
盡管正常情況下清管器會在幾個小時內溶解，但溶解率是關于流體溫度、流體移動、摩擦和原油吸收力的一個函數。 - This product is widely used in high building , oven , baking room , etc . it canbe operated continuously if the fluid temperature under 150 , and more than 40 minutes if the fluid temperature over 300
本產品廣泛應用于高層建筑，烘箱、烘房等的高溫氣體通排風。介質溫度小于150可長期運行，溫度大于300可連續運行40分鐘以上。 - Fist we resarch local wall temperature ouside and inside of tube , local fluid temperature inside and outside of tube , local heat flux inside and outside of tube , local coefficient of convective heat transfer inside and ouside of tube along the tube axial direction
首先研究在這兩種情況下管內(外)壁溫、管內(外)流溫、管內(外)壁面局部熱流密度、管內(外)局部對流換熱系數沿管子軸向的變化。 - It's difficult to find fluid temperature in a sentence. 用fluid temperature造句挺難的
- Analyzing of the heat transfer in microchannel heat sinks , finite element method is used to calculate the surface temperature , fluid temperature and the total thermal resistance of microchannel heat sinks with arbitrary base heat flux distribution
在對微管道散熱器進行傳熱分析時，本文利用有限元法在微管道底壁熱量任意分布的情況下，計算了微管道的壁面溫度和流體溫度分布，最終得到了總熱阻值。 - This program can predict the wall temperature 、 internal wall heat tranfer coefficient 、 fluid temperature and entropy profile along the water wall . all of these provide an important foundation for designing this type of water wall structure to ensure the safety of the boiler operation . this hydrodynamic calculation program and the results can be used to analyze operation reliability and structure design of water wall system
利用所開發的程序?qū)υO(shè)計的超臨界cfb進行了計算，給出不同負荷下，水冷壁出口工質溫度分布，水冷壁受熱面不同位置處的金屬壁溫、內壁放熱系數、流體溫度焓值分布，以及不同管子的流動壓降等結果，為分析鍋爐工作可靠性及水冷壁系統的結構設計提供了重要依據。 - The project studied the direct contact condensation behavior of saturated steam on the subcooled liquid in passive gravity injection system . the experiment parameters were as follows : the initial pressure of prz ranged from 0 . 2 0 . 6mpa and the initial fluid temperature of core makeup tank ranged from 10 80 . condensation phenomenon in cmt was observed
本課題進行了非能動重力補水系統中飽和蒸汽在過冷液面上直接接觸冷凝的實驗研究，研究了在加裝遮流板時，系統壓力0 . 2 0 . 6mpa ， cmt初始溫度為10 80條件下壓力容器cmt中飽和蒸汽在過冷液面上冷凝的瞬態特性。